Detail publikačního výsledku

Analysis of the oxide occurrence on WEDM surfaces in relation to subsequent surface treatments

MOURALOVÁ, K.; PROKEŠ, T.; BENEŠ, L.

Originální název

Analysis of the oxide occurrence on WEDM surfaces in relation to subsequent surface treatments

Anglický název

Analysis of the oxide occurrence on WEDM surfaces in relation to subsequent surface treatments

Druh

Článek WoS

Originální abstrakt

Surface treatments are typical surface protection against corrosion or serve to create an attractive appearance for the end customer. However, the surface to which they are applied must be completely oxide-free, otherwise, defects occur which can cause subsequent corrosion or deterioration of the visual appearance of the product. The parts manufactured by wire electrical discharge machining (WEDM), however, have a high tendency to oxidize. For this reason, this study was aimed at demonstrating the effect of machine setup parameters (gap voltage, pulse on and off time, wire feed and discharge current) on oxygen occurrence on the surface of two non-metallic (aluminium alloy 7475-T7351, chromium nickel superalloy Inconel 625) and four metallic materials (tool alloy steel X210Cr12, Hadfield steel, Creusabro 4800 and Hardox 400). Within this study, 18 samples were produced, where the chemical composition of EDX was analysed, on the basis of which the effect of these parameters on the surface oxidation was proved.

Anglický abstrakt

Surface treatments are typical surface protection against corrosion or serve to create an attractive appearance for the end customer. However, the surface to which they are applied must be completely oxide-free, otherwise, defects occur which can cause subsequent corrosion or deterioration of the visual appearance of the product. The parts manufactured by wire electrical discharge machining (WEDM), however, have a high tendency to oxidize. For this reason, this study was aimed at demonstrating the effect of machine setup parameters (gap voltage, pulse on and off time, wire feed and discharge current) on oxygen occurrence on the surface of two non-metallic (aluminium alloy 7475-T7351, chromium nickel superalloy Inconel 625) and four metallic materials (tool alloy steel X210Cr12, Hadfield steel, Creusabro 4800 and Hardox 400). Within this study, 18 samples were produced, where the chemical composition of EDX was analysed, on the basis of which the effect of these parameters on the surface oxidation was proved.

Klíčová slova

WEDM, electrical discharge machining, EDX, oxide, surface treatment, machining parameters

Klíčová slova v angličtině

WEDM, electrical discharge machining, EDX, oxide, surface treatment, machining parameters

Autoři

MOURALOVÁ, K.; PROKEŠ, T.; BENEŠ, L.

Rok RIV

2020

Vydáno

27.08.2019

Nakladatel

Sage Journals

Místo

Spojené království Velké Británie a Severního Irska

ISSN

0954-4062

Periodikum

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE

Svazek

234

Číslo

3

Stát

Spojené království Velké Británie a Severního Irska

Strany od

721

Strany do

733

Strany počet

13

URL

https://doi.org/10.1177/0954406219884974

BibTex

@article{BUT158176,
  author="Kateřina {Mouralová} and Tomáš {Prokeš} and Libor {Beneš}",
  title="Analysis of the oxide occurrence on WEDM surfaces in relation to subsequent surface treatments",
  journal="PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE",
  year="2019",
  volume="234",
  number="3",
  pages="721--733",
  doi="10.1177/0954406219884974",
  issn="0954-4062",
  url="https://doi.org/10.1177/0954406219884974"
}