Přístupnostní navigace
E-application
Search Search Close
doc. Ing.
Ph.D.
FME, IMID DCM – Associate professor
+420 54114 3260Milan.Klapka@vut.cz
Send BUT message
2025
NAVRÁTIL, V.; KVARDA, D.; KLAPKA, M.; GALAS, R.; OMASTA, M.; KŘUPKA, I.; HARTL, M. Investigation of squeal noise generation in wheel-rail contact under wet conditions using a twin-disc test rig. Proceedings of the Institution of Mechanical Engineers. Part F, Journal of Rail and Rapid Transit, 2025, vol. 8, no. 239, p. 635-645.
WoS Article
2024
VALENA, M.; OMASTA, M.; KLAPKA, M.; GALAS, R.; NAVRÁTIL, V.; KŘUPKA, I.; HARTL, M. Case Study: Correlations Between Curve Squeal, Weather Conditions, and Traction in a Tram Loop. Tribology in Industry, 2024, vol. 46, no. 4, p. 695-708. ISSN: 0354-8996.
Scopus Article
NAVRÁTIL, V.; GALAS, R.; KLAPKA, M.; KVARDA, D.; OMASTA. Wheel Squeal Mitigation Under Water Lubrication. Tribology in Industry, 2024, vol. 46, no. 3, p. 418-431. ISSN: 0354-8996.
2023
KLAPKA, M.; MAZŮREK, I.; NOVÁK, P. Experimental verification of the new methodology for assessment of the relative adhesion. INTERNATIONAL JOURNAL OF VEHICLE DESIGN, 2023, vol. 91, no. 4, p. 342-359. ISSN: 0143-3369.
2022
NAVRÁTIL, V.; GALAS, R.; KLAPKA, M.; KVARDA, D.; OMASTA, M.; SHI, L.; DING, H.; WANG, W.; KŘUPKA, I.; HARTL, M. Wheel Squeal Noise in Rail Transport: The Effect of Friction Modifier Composition. Tribology in Industry, 2022, vol. 44, no. 3, p. 361-373. ISSN: 0354-8996.
OMASTA, M.; NAVRÁTIL, V.; GABRIEL, T.; GALAS, R.; KLAPKA, M. Design and development of a twin disc test rig for the study of squeal noise from the wheel – rail interface. Applied Engineering Letters, 2022, vol. 7, no. 1, p. 10-16. ISSN: 2466-4677.
2021
OMASTA, M.; NAVRÁTIL, V.; GALAS, R.; KLAPKA, M. Design of the twin-disc test rig for the study of wheel squeal noise. 10th International Conference on Tribology – BALKANTRIB '20 PROCEEDINGS. Belgrade: University of Belgrade, Faculty of Mechanical Engineering, 2021. 2 p. ISBN: 978-86-6060-073-0.
Conference proceedings
2018
HALAMA, J.; KLAPKA, M.; MAZŮREK, I. Experimental Methodology for Acoustic Diagnostics of Shock Absorbers. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 2018, vol. 66, no. 5, p. 1119-1125. ISSN: 1211-8516.
2017
KLAPKA, M.; MAZŮREK, I.; KUBÍK, M.; MACHÁČEK, O. Reinvention of the EUSAMA diagnostic methodology. INTERNATIONAL JOURNAL OF VEHICLE DESIGN, 2017, vol. 4, no. 74, p. 304-318. ISSN: 0143-3369.
GALAS, R.; OMASTA, M.; KLAPKA, M.; KAEWUNRUEN, S.; KŘUPKA, I.; HARTL, M. Case study: the influence of oil-based friction modifier quantity on tram braking distance and noise. Tribology in Industry, 2017, vol. 39, no. 2, p. 198-206. ISSN: 0354-8996.
2016
PANÁČEK, T.; KLAPKA, M. Reduction of pneumatic tyred roller fuel consumption. Applied Mechanics and Materials, 2016, vol. 821, no. 1, p. 614-619. ISSN: 1662-7482.
Peer-reviewed article not indexed in WoS or Scopus
KLAPKA, M.; MAZŮREK, I.; MACHÁČEK, O.; KUBÍK, M. Twilight of the EUSAMA diagnostic methodology. MECCANICA, 2016, vol. 52, no. 9, p. 2023-2034. ISSN: 0025-6455.
KLAPKA, M.; MAZŮREK, I.; MACHÁČEK, O. ANALYSIS OF CAUSES OF FALSE-NEGATIVE EVALUATION OF EUSAMA METHODOLOGY FOR SUSPENSION ASESSMENT. In Engineering mechanics 2016. Prague: Institute of Thermomechanics, Academy of Sciences of the Czech Republic, 2016. p. 282-285. ISBN: 978-80-87012-59-8.
Paper in proceedings (conference paper)
2015
STRECKER, Z.; ROUPEC, J.; MAZŮREK, I.; KLAPKA, M. Limiting factors of the response time of the magnetorheological damper. INTERNATIONAL JOURNAL OF APPLIED ELECTROMAGNETICS AND MECHANICS, 2015, vol. 47, no. 2, p. 541-550. ISSN: 1383-5416.
STRECKER, Z.; MAZŮREK, I.; ROUPEC, J.; MACHÁČEK, O.; KUBÍK, M.; KLAPKA, M. Design of magnetorheological damper with short time response. JOURNAL OF INTELLIGENT MATERIAL SYSTEMS AND STRUCTURES, 2015, vol. 26, no. 14, p. 1951-1958. ISSN: 1045-389X.
STRECKER, Z.; MAZŮREK, I.; ROUPEC, J.; KLAPKA, M. Influence of MR damper response time on semiactive suspension control efficiency. MECCANICA, 2015, vol. 50, no. 8, p. 1949-1959. ISSN: 0025-6455.
KLAPKA, M.; PANÁČEK, T.; NEVRLÝ, J. Experimental rig for simulation of hydromechanical system with energy regeneration. Engineering Mechanics, 2015, vol. 21, no. 5, p. 305-309. ISSN: 1805-4633.
2014
PANÁČEK, T.; KLAPKA, M.; NĚMEC, Z. Optimization of valve manifold timing sequence using differential evolution algorithm. In Engineering mechanics 2014, Book of full texts. 1. Prague: Institute of Termomechanics, Academy of Sciences of the Czech Republic, 2014. p. 468-471. ISBN: 978-80-214-4871-1.
SZENDIUCH, I.; OTÁHAL, A.; PSOTA, B.; KLAPKA, M. Vibration Testing as a Tool to Optimize the Configuration of the PCBs. In IMAPS Proceedings. 1. San Diego, USA: IMAPS, 2014. p. 50-54. ISBN: 978-0-9909028-0-5.
2013
MAZŮREK, I.; ROUPEC, J.; KLAPKA, M.; STRECKER, Z. Load and rheometric unit for the test of magnetorheological fluid. MECCANICA, 2013, vol. 48, no. 3, p. 631-641. ISSN: 0025-6455.
SZENDIUCH, I.; KLAPKA, M.; PSOTA, B.; OTÁHAL, A. Importance of Vibration Testing for New Technological Solutions. In Proceedings EMPC 2013. 1. Grenoble: IMAPS France, 2013. no. 1, p. 144-148. ISBN: 978-2-9527467-1-7.
Josef Nevrlý, Miroslav Jurík, Zdeněk Němec, Milan Klapka, Štěpán Drha, Tomáš Panáček. Use of experimental stand for research kinetic energy recovery. In The 22nd International Conference on Hydraulics and Pneumatics. Ostrava: VŠB-TU Ostrava, 2013. p. 195-202. ISBN: 978-80-248-3136-7.
2012
ROUPEC, J.; MAZŮREK, I.; STRECKER, Z.; KLAPKA, M. The Behavior of the MR Fluid During Durability Test. Journal of Physics: Conference Series, 2012, vol. 412, no. 1, p. 1-8. ISSN: 1742-6588.
2011
KLAPKA, M.; MAZŮREK, I. Assessment of the stub-shaft sleeve bearing chaotic behavior in automotive differential. In Mechatronics: Recent technological and scientific advances. 1. Berlin: Springer-Verlag Berlin Heidelberg, 2011. p. 303-308. ISBN: 978-3-642-23243-5.
KLAPKA, M.; MAZŮREK, I.; STRECKER, Z. The analysis of automotive differential vibrations by means of bifurcation diagrams. In Engineering Mechanics 2011, Book of full texts. 1. Prague: Institute of Termomechanics, Academy of Sciences of the Czech Republic, 2011. p. 287-290. ISBN: 978-80-87012-33-8.
2010
KLAPKA, M.; MAZŮREK, I.; ROUPEC, J. Radial flexible bearings suitable stiffness estimation. MECCANICA, 2010, vol. 46, no. 2, p. 293-392. ISSN: 0025-6455.
2009
ROUPEC, J.; MAZŮREK, I.; KLAPKA, M.; ČÍŽ, P. Identification of MR Fluids properties in Mechatronic Damping Elements. In Recent Advances in Mechatronics 2008 - 2009. Berlin, Heidelberg: Springer-Verlag Berlin Heidelberg, 2009. p. 115-120. ISBN: 978-3-642-05021-3.
MAZŮREK, I.; KLAPKA, M.; ROUPEC, J. Noise Reduction of the Differential Sleeve Bearing. Engineering Mechanics, 2009, vol. 16, no. 2, p. 93-102. ISSN: 1802-1484.
2008
KLAPKA, M.; ROUPEC, J.; MAZŮREK, I. Evaluation Method of Sleeve Bearing Noise from Vibrations Data. In International Conference on Fascinating Advancements in Mechanical Engineering Proceedings. Mepco Engg. College - 626005, Sivakasi, Virudhunagar district, Tamilnadu, India: Mepco Schlenck Engineering College Sivakasi, 2008. p. 483-489. ISBN: 978-81-907108-0-0.
KLAPKA, M.; ROUPEC, J. Roller bearing fatigue test with help of CAN bus and internet. In 49. Mezinárodní konference kateder částí a mechanismů strojů. Plzeň: Západočeská univerzita v Plzni, 2008. p. 129-132. ISBN: 978-80-7043-718-6.
KLAPKA, M.; MAZŮREK, I. Analytical software for evaluation of noise emission quality of the sleeve journal bearing. In 31. mezinárodní konference TD 2008 - DIAGON 2008 - Sborník přednášek. Academia Centrum UTB, Mostní 5139, Zlín: Academia centrum UTB ve Zlíně, 2008. p. 60-65. ISBN: 978-80-7318-707-1.
2007
MAZŮREK, I.; KLAPKA, M. Noise emission of the mechatronic system. In Simulation Modelling of Mechatronic Systems III. mechatronics. Brno: Faculty of Mechanical Engineering, Brno University of Technology, 2007. p. 165-176. ISBN: 978-80-214-3559-9.
Chapter in a book
KLAPKA, M.; MAZŮREK, I. Vibration behavior of the sleeve journal bearing. In Sborník přednášek 30. mezinárodní konference TD 2007 – DIAGON 2007. 2007. Zlín: Academia centrum UTB ve Zlíně, 2007. p. 130-135. ISBN: 978-80-7318-570-1.
MAZŮREK, I.; DVOŘÁČEK, P.; KLAPKA, M. Using Network CAN-BUS for Assessment Transmission Load of Vehicle. In Engineering mechanics. 2007. Praha: Institute of Theoretical and Applied Mechanics Academy of Science of Czech Republic, 2007. p. 181-182. ISBN: 978-80-87012-06-2.
MAZŮREK, I.; PRAŽÁK, F.; KLAPKA, M. Over-crossing test to evaluation of shock absorber. In Recent Advances in Mechatronics. 2007. Heidelberg: Springer Verlag, 2007. p. 425-432. ISBN: 978-3-540-73955-5.
KLAPKA, M.; MAZŮREK, I.; DVOŘÁČEK, P. Automotive Electronic System on Instructional Board. In Sborník příspěvků 48. mezinárodní konference částí strojů a mechanizmů. 2007. Bratislava: Slovenská technická univerzita, 2007. p. 433-436. ISBN: 978-80-227-2708-2.
KLAPKA, M.; MAZŮREK, I.; PRAŽÁK, F. Diagnostic and education board of monitoring system. In Sborník přednášek 30. mezinárodní konference TD 2007 – DIAGON 2007. 2007. Zlín: Academia centrum UTB ve Zlíně, 2007. p. 93-96. ISBN: 978-80-7318-570-1.
KLAPKA, M.; MAZŮREK, I. The Behavior Of the Sleeve journal bearing Under External Vibrations. In Sborník příspěvků 48. mezinárodní konference částí strojů a mechanizmů. 2007. Bratislava: Slovenská technická univerzita, 2007. p. 425-432. ISBN: 978-80-227-2708-2.
2006
KLAPKA, M. Studium vibrací kluzného uložení. In sborník prací 47. konference KCMS. Praha: Česká zemědělská univerzita v Praze, 2006. s. 154-157. ISBN: 80-213-1523-7.
*) Citations are generated once every 24 hours.