Přístupnostní navigace
E-application
Search Search Close
Doctoral Thesis
Author of thesis: Ing. Pavlína Šárfy, DiS.
Acad. year: 2026/2027
Supervisor: prof. Ing. Klára Částková, Ph.D.
Reviewers: doc. Ing. Eva Bartoníčková, Ph.D., Assoc. Prof. José Joaquín Velázquez García, Ph.D.
The aim of this doctoral thesis was to develop a fully ceramic scaffold with a hybrid structure combining load-bearing function with the porosity required for bone ingrowth. In porous ceramics these two requirements are in conflict, since increasing the porosity generally reduces the mechanical resistance. The thesis is divided into two parts. The first part deals with the preparation and characterization of hydroxyapatite foams and of dense substrates made from the same ceramic powder. The polyurethane direct foaming method was extended to processing variables not previously examined for hydroxyapatite suspensions — the chain extender 1,4-butanediol, four dispersants of two stabilization classes, two isocyanate grades of different viscosity, and curing under reduced pressure — and beyond the previously published ranges of the isocyanate index and water content. The optimized formulation gave foams with a porosity of 69 % and a mean pore size of 125 µm determined by µCT, with an interconnected pore network and an isolated pore volume fraction below 0.2 %. The screening showed that the values maximizing porosity or pore size gave foams that disintegrated during handling; the selection of every parameter was therefore governed by structural coherence. Undoped hydroxyapatite remained phase-stable up to 1250 °C, while the composition containing 5 wt.% silica proved compatible with the same foaming route at the cost of an approximately fivefold increase in the extent of hydroxyapatite decomposition. MG-63 cells remained viable on the hydroxyapatite foams across the whole range of sintering temperatures, with metabolic activity increasing between day 3 and day 7. Since a porous foam does not provide a reflective surface, dense substrates were prepared from the same powder and used to establish the conditions under which reflective holographic microscopy can be applied to hydroxyapatite — a technique that allows living cells to be observed non-invasively, without labelling or fixation. The polishing sequence was related to the resulting surface roughness, wettability and holographic image contrast, and the technique was compared on the same surfaces with scanning electron microscopy, atomic force microscopy and confocal laser scanning microscopy. The criterion for reliable phase reconstruction applies to the roughness of the material between the pores rather than to the areal value, and polishing to 1 µm proved sufficient. The second part deals with the development of the hybrid scaffold itself: a load-bearing hydroxyapatite cage produced by digital light processing and filled with a foam of the same hydroxyapatite. Two processing variables proved decisive. As-printed cages cracked during foam expansion at both wall thicknesses examined, so the cage had to be sintered before filling. Of the treatment temperatures subsequently tested, only 900 °C both removed the polymeric network and retained the mechanical interlock formed where the foam penetrates the perforations of the cage wall; above this temperature the foam progressively withdrew from the perforations, and at 1250 °C it detached from the cage completely. The optimized scaffold reached a characteristic compressive strength of 53.5 MPa at a Weibull modulus of 7.76. The concept was transferred to the application-relevant geometry of an interbody fusion cage and registered as a functional sample.
Hydroxyapatite; bone tissue engineering; ceramic scaffold; hybrid structure; polyurethane direct foaming; digital light processing; compressive strength; Weibull statistics; reflective holographic microscopy
Date of defence
30.09.2026
Result of the defence
Defended (thesis was successfully defended)
Process of defence
Disertační práce Ing. Šárfy se zabývá vývojem plně keramických hybridních scaffoldů kombinujících mechanickou únosnost s vysokou porozitou potřebnou pro prorůstání kostní tkáně. První část práce je zaměřena na optimalizaci hydroxyapatitových pěn, které dosáhly porozity 69 %, střední velikosti pórů 125 µm a podílu izolovaných pórů pod 0,2 %, a na stanovení podmínek pro využití reflexní holografické mikroskopie na hutných hydroxyapatitových substrátech. Druhá část se věnuje vývoji hybridního skafoldu tvořeného DLP tištěnou hydroxyapatitovou klecí a hydroxyapatitovou pěnou, přičemž optimalizované řešení dosáhlo pevnosti v tlaku 53,5 MPa při Weibullově modulu 7,76. Navržený koncept byl následně převeden do geometrie meziobratlové fúzní klece a registrován jako funkční vzorek. Práce systematicky propojuje pokročilé výrobní strategie s komplexní charakterizací a představuje významný přínos k rozvoji biokeramických materiálů a kostního tkáňového inženýrství. Stanovené cíle práce byly splněny a její výsledky prokazují jak vědecký, tak praktický a aplikační potenciál navrženého řešení. Během obhajoby studentka prokázala velmi dobré odborné znalosti v dané oblasti a na dotazy oponentů i členů komise odpověděla uspokojivě.
Language of thesis
English
Faculty
Středoevropský technologický institut VUT
Department
Central European Institute of Technology BUT
Study programme
Advanced Materials and Nanosciences (CEITEC-AMN-CZ-P)
Composition of Committee
prof. Ing. Radimír Vrba, CSc. (předseda) prof. RNDr. Karel Maca, Dr. (místopředseda) doc. Ing. Vít Jan, Ph.D. (člen) doc. Ing. Eva Bartoníčková, Ph.D. (člen) Assoc. Prof. José Joaquín Velázquez García, Ph.D. (člen) Ing. Hynek Hadraba, Ph.D. (člen)
Supervisor’s reportprof. Ing. Klára Částková, Ph.D.
Reviewer’s reportdoc. Ing. Eva Bartoníčková, Ph.D.
Reviewer’s reportAssoc. Prof. José Joaquín Velázquez García, Ph.D.
Responsibility: Mgr. et Mgr. Hana Odstrčilová