V rámci projektu budou zkoumány vlastnosti materiálů připravovaných aditivními technologiemi (metody SLM a Cold Spray). Vlastní řešení bude rozděleno do 3 oblastí - viz cíle. Ve všech případech se jedná o vysoce aktuální problematiku s přímým dopadem na průmyslové aplikace.

FSI-S-23-8305

Czech

Pantělejev Libor, prof. Ing., Ph.D. - principal person responsible
Doubrava Marek, Ing., Ph.D. - fellow researcher

Institute of Materials Science and Engineering
- responsible department (24.4.2024 - not assigned)
Institute of Materials Science and Engineering
- internal (1.1.2023 - 31.12.2025)
Faculty of Mechanical Engineering
- beneficiary (1.1.2023 - 31.12.2025)

Štěpán Kolomý, Marek Doubrava, Martin Harant, Daniel Chrást, Milan Forejt, Josef Sedlák. The effect of heat treatment and strain rate on the mechanical behaviour of aluminium alloy 2024. International Journal of Advanced Manufacturing Technology, 2026, no. March 2026, 14 p.
Detail

POLOPRUDSKÝ, J.; KLICHTOVÁ, D.; STOLÁRIK, G.; CHLUPOVÁ, A. EFFECT OF TECHNOLOGICAL PARAMETERS OF THE PULSATING WATER JET ON EROSION EFFECTIVITY ON A LINEAR TRAJECTORY. MM Science Journal, 2024, vol. October, no. October, p. 7526-7533. ISSN: 1805-0476.
Detail

HLOCH, S.; POLOPRUDSKÝ, J.; ŠIŠKA, F.; BABINSKÝ, T.; NAGH, A.; CHLUPOVÁ, A.; KRUML, T. Erosion development in AISI 316L stainless steel under pulsating water jet treatment. Engineering Science and Technology, an International Journal, 2024, vol. 50, no. 1, p. 1-14. ISSN: 2215-0986.
Detail

VAVERKA, O.; ČERVINEK, O.; JAROŠ, J.; KOUTNÝ, D.; PANTĚLEJEV, L. Numerical and Experimental Evaluation of Structured Material for Use in Multi-scale Topology Optimization. Advanced engineering materials, 2024, vol. 26, no. 13, p. 1-10. ISSN: 1527-2648.
Detail

Poloprudský, J.;Gamanov, Š.; Chlupová, A.; Klichová, D.; Nag, A.; Stolárik, G.; Hloch S. Water droplet erosion assessment in the initial stages on AISI 316 L using kernel average misorientation. Tribology International, 2024, vol. 191, no. March, p. 1-14. ISSN: 1879-2464.
Detail

MALEKI, E.; UNAL, O.; DOUBRAVA, M.; PANTĚLEJEV, L.; BAGHERIFARD, S.; GUAGLIANO, M. Application of impact-based and laser-based surface severe plastic deformation methods on additively manufactured 316L: Microstructure, tensile and fatigue behaviors. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2024, vol. 916, no. October, p. 1-17. ISSN: 0921-5093.
Detail

VAŠÁKOVÁ, K.; JUDAS, J.; ČUPERA, J.; PANTĚLEJEV, L.; KOUTNÝ, D. Effects of heat treatment on microstructure and mechanical properties of LPBF AlSi9Cu3 alloy. In Procedia Structural Integrity. Procedia Structural Integrity. Nizozemí: Elsevier B.V., 2025. no. prosinec, p. 99-105.
Detail

KOLOMÝ, Š.; SLANÝ, M.; DOUBRAVA, M.; SEDLÁK, J.; ZOUHAR, J.; ŘEHOŘEK, L. Comparative analysis of machinability and microstructure in LPBF and conventionally processed M300 maraging steel. Scientific Reports, 2025, vol. 15, no. October, p. 1-21.
Detail

VRAŽINA, T.; BRŮŽA, J.; CHLUPOVÁ, A.; ŠULÁK, I.; PANTĚLEJEV, L.; KRUML, T.; MAN, J. Advanced Semantic Segmentation of Cellular Substructure in Selectively Laser Melted 316L Stainless Steel. In Procedia Structural Integrity. Procedia Structural Integrity. Elsevier BV, 2025. p. 106-113.
Detail

DOUBRAVA, M.; ŘEHOŘEK, L.; PANTĚLEJEV, L. DEVELOPMENT OF A METHODOLOGY FOR SCRATCH TESTING COLD SPRAY COATINGS. In METAL-Conference Proceedings. Metal ... SLEZSKA: Tanger Ltd, 2024. p. 305-310.
Detail

Responsibility: Pantělejev Libor, prof. Ing., Ph.D.